SERVICE PROCEDURES

2027 40mm FLOAT NA3 Glidecore Rebuild

Required Parts

  • 803-04-703 Seal Kit: 2027 40 FLOAT NA 3 Glidecore Rebuild, Two Piece Neg Plate

Required Tools

  • 398-00-657 Tooling: Bullet, Sealhead To Shaft, FLOAT NA 2
  • 398-00-681 2002-017 32 Damper-side and ALL 32-34-36-40 Spring-side Removal Tool
  • 398-00-682 2005-017 34-36-40 Damper-side Removal Tool
  • 398-00-706 Tooling: Fork Topcap Socket, 32mm V2, 3/8 Drive
  • 398-01-298 Tooling: Custom Hex Socket, 22mm, 2026 36 & 36 E-Opt, Neg Plate
  • 803-01-324 Kit: Tooling: 2019 Clamps, Grip Damper, Body and Shaft

Supplies Needed

  • 10mm Socket
  • 12mm Crows Foot
  • 12mm Wrench
  • 15mm Socket
  • 2mm Hex Wrench
  • 4mm Hex Wrench
  • 5mm Hex Wrench
  • Mallet
  • Propane Torch
  • Ratchet
  • Seal Pick
  • Shock pump
  • Torque Wrench

WARNING: Always wear safety glasses and protective gloves during service to prevent potential injury. Failure to wear protective equipment during service may lead to SERIOUS INJURY OR DEATH.

The following procedure guides you through the rebuild of the FLOAT NA3 Glide core air spring found in 2027 40mm forks.

WARNING: FOX products should be serviced by a trained bicycle service technician, in accordance with FOX specifications. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it. Improperly serviced products can fail, causing the rider to lose control resulting in SERIOUS INJURY OR DEATH.

WARNING: Never attempt to modify air volume spacers or air shaft assemblies, as this can damage your fork causing a loss of control of the bicycle leading to SERIOUS INJURY or DEATH.

WARNING: FOX suspension products contain pressurized nitrogen, air, oil, or all 3. Suspension misuse can cause property damage, SERIOUS INJURY OR DEATH. DO NOT puncture, incinerate or crush any portion of a FOX suspension product. DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.

WARNING: Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH. DO NOT modify any part of a fork or shock, including the fork brace (lower leg cross brace), crown, steerer, upper and lower leg tubes, or internal parts, except as instructed herein. Any unauthorized modification may void the warranty, and may cause failure or the fork or shock, resulting in SERIOUS INJURY OR DEATH.

WARNING: Please verify that all air has been released from the air chamber by pushing down on the Schrader valve core. Failure to release all air pressure before further disassembly may cause parts to eject causing SEVERE INJURY OR DEATH.

img/help/page3217-RDLC/IMG_1994 copy-m.jpg

Step 1

Wipe the grease off the air shaft assembly to make it easier to handle. Clamp the piston body securely in a soft-jaw vise. 

img/help/page3217-RDLC/IMG_1994 copy.jpg
img/help/page3217-RDLC/IMG_1995 copy.jpg


img/help/page3217-RDLC/IMG_1996 copy-m.jpg

Step 2

Unthread the air piston counterclockwise using a 10 mm socket. Lift the dome-shaped piston off the piston base to remove it. Remove the piston band , and set it aside

img/help/page3217-RDLC/IMG_1996 copy.jpg
img/help/page3217-RDLC/IMG_1997 copy.jpg
img/help/page3217-RDLC/IMG_1998 copy.jpg


img/help/page3217-RDLC/IMG_1999 copy-m.jpg

Step 3

Remove the Q-ring from the piston and replace it with a new greased one from the kit. Reinstall the gray piston band.

img/help/page3217-RDLC/IMG_1999 copy.jpg
img/help/page3217-RDLC/IMG_2000 copy.jpg
img/help/page3217-RDLC/IMG_2001 copy.jpg
img/help/page3217-RDLC/IMG_2002 copy.jpg


img/help/page3217-RDLC/IMG_2013 copy-m.jpg

Step 4

Clean the shaft with isopropyl alcohol, then clamp it securely in the 10 mm Shaft Clamps (PN: 803-01-324). Using a 4 mm Allen wrench, unthread the piston bolt counterclockwise.

img/help/page3217-RDLC/IMG_2013 copy.jpg
img/help/page3217-RDLC/IMG_2014 copy.jpg
img/help/page3217-RDLC/IMG_2015 copy.jpg


img/help/page3217-RDLC/IMG_2018 copy-m.jpg

Step 5

Remove the O-ring from the piston bolt, then remove the top-out spacer from the shaft. Clamp the piston body securely in a soft-jaw vise. Using an 18 mm socket, unthread and remove the piston cap.

img/help/page3217-RDLC/IMG_2018 copy.jpg
img/help/page3217-RDLC/IMG_2019 copy.jpg
img/help/page3217-RDLC/IMG_2020 copy.jpg
img/help/page3217-RDLC/IMG_2021 copy.jpg
img/help/page3217-RDLC/IMG_2022 copy.jpg


img/help/page3217-RDLC/IMG_2023 copy-m.jpg

Step 6

Remove the piston bolt and replace the compliance O-rings with new, greased O-rings from the kit. Reinstall the piston bolt onto the piston cap. Apply 1–2 drops of red Loctite 263 to the threads, then thread the piston cap onto the piston body and torque to 80 in-lb(9Nm).

img/help/page3217-RDLC/IMG_2023 copy.jpg
img/help/page3217-RDLC/IMG_2024 copy.jpg
img/help/page3217-RDLC/IMG_2025 copy.jpg
img/help/page3217-RDLC/IMG_2026 copy.jpg
img/help/page3217-RDLC/IMG_2027 copy.jpg
img/help/page3217-RDLC/IMG_2028 [Recovered] copy.jpg


img/help/page3217-RDLC/IMG_2029 copy-m.jpg

Step 7

Reinstall the top-out spacer, followed by the piston bolt O-ring. Apply 1–2 drops of red Loctite 263 to the air shaft threads, then install the piston bolt and torque to 50 in-lb(5.6Nm).

img/help/page3217-RDLC/IMG_2029 copy.jpg
img/help/page3217-RDLC/IMG_2030 copy.jpg
img/help/page3217-RDLC/IMG_2032 copy.jpg
img/help/page3217-RDLC/IMG_2033 copy.jpg
img/help/page3217-RDLC/IMG_2034 copy.jpg


img/help/page3217-RDLC/IMG_2036 copy-m.jpg

Step 8

Clamp the piston body securely in a soft-jaw vise. Reinstall the domed piston onto the piston body. Using a 10 mm socket, torque the domed piston to 120 in-lb (13.6 Nm).

img/help/page3217-RDLC/IMG_2036 copy.jpg
img/help/page3217-RDLC/IMG_2037 copy-1.jpg


img/help/page3217-RDLC/IMG_2004 copy-m.jpg

Step 9

Clean the shaft with Isopropyl alcohol then clamp it in your 10mm shaft clamps (PN: 803-01-324). Remove and discard the o-ring from the base stud.

img/help/page3217-RDLC/IMG_2004 copy.jpg


img/help/page3217-RDLC/IMG_2006 copy-m.jpg

Step 10

Carefully apply heat to the shaft at the base stud with a propane torch for 5-10 seconds to break down the Loctite. Unthread the base stud counter-clockwise with a 12mm wrench, then lift up to remove. Remove MCU bumper and Neg plate. 

img/help/page3217-RDLC/IMG_2006 copy.jpg
img/help/page3217-RDLC/IMG_2007 copy-2.jpg
img/help/page3217-RDLC/IMG_2008 copy.jpg
img/help/page3217-RDLC/IMG_2009 copy.jpg
img/help/page3217-RDLC/IMG_2010 copy.jpg


img/help/page3217-RDLC/IMG_2038 copy-m.jpg

Step 11

Insert a 4 mm hex wrench through the holes in the negative plate tube and hold it securely. Using the Negative Plate Socket (PN: 398-01-298), hold the socket firmly against the negative plate and unthread it counterclockwise from the negative plate tube.

img/help/page3217-RDLC/IMG_2038 copy.jpg
img/help/page3217-RDLC/IMG_2039 copy.jpg
img/help/page3217-RDLC/IMG_2040 copy.jpg


img/help/page3217-RDLC/IMG_2044 copy-m.jpg

Step 12

Remove the seal carrier from the negative plate housing. Remove the compliance O-ring, Q-ring, and housing O-ring, then replace them with new, greased ones from the kit.

img/help/page3217-RDLC/IMG_2044 copy.jpg
img/help/page3217-RDLC/IMG_2045 copy.jpg
img/help/page3217-RDLC/IMG_2046 copy.jpg
img/help/page3217-RDLC/IMG_2047 copy.jpg
img/help/page3217-RDLC/IMG_2048 copy.jpg


img/help/page3217-RDLC/IMG_2049 copy-m.jpg

Step 13

Reinstall the seal carrier. Apply 1–2 drops of blue Loctite 243 to the capture plate threads, then install and torque the capture plate to 50 in-lb using the Negative Plate Socket (PN: 398-01-298).

img/help/page3217-RDLC/IMG_2049 copy.jpg
img/help/page3217-RDLC/IMG_2050 copy.jpg
img/help/page3217-RDLC/IMG_2052 copy.jpg
img/help/page3217-RDLC/IMG_2053 copy.jpg


img/help/page3217-RDLC/IMG_2054 copy-m.jpg

Step 14

Reinstall the top-out bumper. Insert the Bullet Tool (PN: 398-00-657) into the shaft, then apply a thin film of Slick Honey. Reinstall the negative plate with the flat side facing down, then the MCU bumper. Remove the bullet tool.

img/help/page3217-RDLC/IMG_2054 copy.jpg
img/help/page3217-RDLC/IMG_2057 copy.jpg
img/help/page3217-RDLC/IMG_2055 copy.jpg
img/help/page3217-RDLC/IMG_2059 copy.jpg


img/help/page3217-RDLC/IMG_2061 copy-m.jpg

Step 15

Apply 1-2 drops of red Loctite 262 to the threads inside the shaft. Insert the base stud and thread it in clockwise, tightening to 50 in-lb (5.7 Nm) torque with a 12mm crow's foot. Install a new greased o-ring from the kit onto the base stud.

img/help/page3217-RDLC/IMG_2061 copy.jpg
img/help/page3217-RDLC/IMG_2064 copy.jpg
img/help/page3217-RDLC/IMG_2065 copy.jpg